Technical parameters
2.1 General
2.1.1 Application This specification is applied to Push Button Switch used for electronic equipment.
2.1.2 Operating temperature range -25鈩?锝?+55鈩?br/> 2.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
2.1.4 Test conditions
Ambient temperature 15~35鈩?br/> Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
If any doubt arise from the judgment, tests shall be conducted at the following conditions.
Ambient temperature锛?20卤2鈩?br/> Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
2.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
2.2.2 Construction and dimensions Refer to individual product drawing.
2.3. ELECTRICAL SPECIFICATION
NO.ItemsTest conditionsRequirements
2.3.1Contact
resistanceMeasured at 1khz small current(100mA or less)
50m惟 MAX
2.3.2Insulation
resistanceApply a voltage of 1000VDC for 1 min.
to following portions after which
measurement shall be made.
between terminals1000M惟 MIN
2.3.3Dielectric
Strength
AC 2000V RMS(50-60HZ)for 1 min trip
between terminals.
Without damage to parts
Arcing or breakdown etc
2.4. ENVIRONMENT RESISTANCE
NO.ItemsTest conditionsRequirements
2.4.1Cold test
The switch shall be stored at a
temperature of -20卤3鈩?for 96 hours.
Then the switch shall be maintained at
standard atmospheric conditions for 1
hour after which measurement shall be made.
There shall be no
deformation or cracks in
Molded part.
2.4.2Heat resistanceThe switch shall be stored at a
temperature of 55卤3鈩?for 96 hours.
Then the switch shall be maintained at
standard atmospheric conditions for 1
hour after which measurement shall be made.
2.4.3Humidity
test
The switch shall be stored ata temperature
of 40卤2鈩?and a humifity of 90% to 95%
for 96 hours.then the switch shall be
maintained at standard atmospheric
condition for 1 hour after which
measurement shall be made.
2.4.4Standard
conditions
Unless otherwise specified.
the standard range of atmospheric
conditions for making measurements
and tests are as follows:
(1)Temperature:40卤2鈩?/p>
(2)Relative Humidity:90~95%
(3)Time:96 hours.
3. DRAWING & DIMENSION:
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment鈥tc.
5.Remarks
PARTS LIST:
NO.quantityItemsMaterial
11BushingStainless Steel
21BasePBT (UL 94-V0), PC( UL 94-V2)
3 1ActuatorPc; Stainless Steel
41Inner AssemblyPOM/ PA66
51SpringSpring Steel
61SealingSilicone
71O-ringSilicone
85Terminal/ ContactCopper, silver plated/ contact锛歝opper , gold plated
91Hex NutNickel plated brass
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Q锛歐hat is your main market?
A:Europe, The North America, South America, Australia, The middle east, and etc.
Q: What鈥檚 your after-sale service?
A: Our quality warranty period is one year. Any quality problem will be solved to customer satisfactions.
Q锛欼s the sample available?
A:Yes, we are providing free of samples are available for you to check the quality once confirmed after 1~2day. Push Button Switch suppliers
website:http://www.switechchina.com/push-button-switch/
2.1 General
2.1.1 Application This specification is applied to Push Button Switch used for electronic equipment.
2.1.2 Operating temperature range -25鈩?锝?+55鈩?br/> 2.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
2.1.4 Test conditions
Ambient temperature 15~35鈩?br/> Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
If any doubt arise from the judgment, tests shall be conducted at the following conditions.
Ambient temperature锛?20卤2鈩?br/> Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
2.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
2.2.2 Construction and dimensions Refer to individual product drawing.
2.3. ELECTRICAL SPECIFICATION
NO.ItemsTest conditionsRequirements
2.3.1Contact
resistanceMeasured at 1khz small current(100mA or less)
50m惟 MAX
2.3.2Insulation
resistanceApply a voltage of 1000VDC for 1 min.
to following portions after which
measurement shall be made.
between terminals1000M惟 MIN
2.3.3Dielectric
Strength
AC 2000V RMS(50-60HZ)for 1 min trip
between terminals.
Without damage to parts
Arcing or breakdown etc
2.4. ENVIRONMENT RESISTANCE
NO.ItemsTest conditionsRequirements
2.4.1Cold test
The switch shall be stored at a
temperature of -20卤3鈩?for 96 hours.
Then the switch shall be maintained at
standard atmospheric conditions for 1
hour after which measurement shall be made.
There shall be no
deformation or cracks in
Molded part.
2.4.2Heat resistanceThe switch shall be stored at a
temperature of 55卤3鈩?for 96 hours.
Then the switch shall be maintained at
standard atmospheric conditions for 1
hour after which measurement shall be made.
2.4.3Humidity
test
The switch shall be stored ata temperature
of 40卤2鈩?and a humifity of 90% to 95%
for 96 hours.then the switch shall be
maintained at standard atmospheric
condition for 1 hour after which
measurement shall be made.
2.4.4Standard
conditions
Unless otherwise specified.
the standard range of atmospheric
conditions for making measurements
and tests are as follows:
(1)Temperature:40卤2鈩?/p>
(2)Relative Humidity:90~95%
(3)Time:96 hours.
3. DRAWING & DIMENSION:
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment鈥tc.
5.Remarks
PARTS LIST:
NO.quantityItemsMaterial
11BushingStainless Steel
21BasePBT (UL 94-V0), PC( UL 94-V2)
3 1ActuatorPc; Stainless Steel
41Inner AssemblyPOM/ PA66
51SpringSpring Steel
61SealingSilicone
71O-ringSilicone
85Terminal/ ContactCopper, silver plated/ contact锛歝opper , gold plated
91Hex NutNickel plated brass
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Q锛歐hat is your main market?
A:Europe, The North America, South America, Australia, The middle east, and etc.
Q: What鈥檚 your after-sale service?
A: Our quality warranty period is one year. Any quality problem will be solved to customer satisfactions.
Q锛欼s the sample available?
A:Yes, we are providing free of samples are available for you to check the quality once confirmed after 1~2day. Push Button Switch suppliers
website:http://www.switechchina.com/push-button-switch/
Technical parameters
2.1 General
2.1.1 Application This specification is applied to Push Button Switch used for electronic equipment.
2.1.2 Operating temperature range -25鈩?锝?+55鈩?br/> 2.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
2.1.4 Test conditions
Ambient temperature 15~35鈩?br/> Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
If any doubt arise from the judgment, tests shall be conducted at the following conditions.
Ambient temperature锛?20卤2鈩?br/> Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
2.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
2.2.2 Construction and dimensions Refer to individual product drawing.
2.3. ELECTRICAL SPECIFICATION
NO.ItemsTest conditionsRequirements
2.3.1Contact
resistanceMeasured at 1khz small current(100mA or less)
50m惟 MAX
2.3.2Insulation
resistanceApply a voltage of 1000VDC for 1 min.
to following portions after which
measurement shall be made.
between terminals1000M惟 MIN
2.3.3Dielectric
Strength
AC 2000V RMS(50-60HZ)for 1 min trip
between terminals.
Without damage to parts
Arcing or breakdown etc
2.4. ENVIRONMENT RESISTANCE
NO.ItemsTest conditionsRequirements
2.4.1Cold test
The switch shall be stored at a
temperature of -20卤3鈩?for 96 hours.
Then the switch shall be maintained at
standard atmospheric conditions for 1
hour after which measurement shall be made.
There shall be no
deformation or cracks in
Molded part.
2.4.2Heat resistanceThe switch shall be stored at a
temperature of 55卤3鈩?for 96 hours.
Then the switch shall be maintained at
standard atmospheric conditions for 1
hour after which measurement shall be made.
2.4.3Humidity
test
The switch shall be stored ata temperature
of 40卤2鈩?and a humifity of 90% to 95%
for 96 hours.then the switch shall be
maintained at standard atmospheric
condition for 1 hour after which
measurement shall be made.
2.4.4Standard
conditions
Unless otherwise specified.
the standard range of atmospheric
conditions for making measurements
and tests are as follows:
(1)Temperature:40卤2鈩?/p>
(2)Relative Humidity:90~95%
(3)Time:96 hours.
3. DRAWING & DIMENSION:
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment鈥tc.
5.Remarks
PARTS LIST:
NO.quantityItemsMaterial
11BushingStainless Steel
21BasePBT (UL 94-V0), PC( UL 94-V2)
3 1ActuatorPc; Stainless Steel
41Inner AssemblyPOM/ PA66
51SpringSpring Steel
61SealingSilicone
71O-ringSilicone
85Terminal/ ContactCopper, silver plated/ contact锛歝opper , gold plated
91Hex NutNickel plated brass
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Q锛歐hat is your main market?
A:Europe, The North America, South America, Australia, The middle east, and etc.
Q: What鈥檚 your after-sale service?
A: Our quality warranty period is one year. Any quality problem will be solved to customer satisfactions.
Q锛欼s the sample available?
A:Yes, we are providing free of samples are available for you to check the quality once confirmed after 1~2day. Push Button Switch suppliers
website:http://www.switechchina.com/push-button-switch/
0 Comments
0 Shares